Cisco 2500控制器初始化配置浏览数:415次
Enter Administrative User Name (24 characters max): cisco //输入设备名称 Enter Administrative Password (24 characters max): ***** //配置管理用户和密码 Re-enter Administrative Password : ***** Management Interface IP Address: 172.16.34.250 // 配置管理接口 注：带内管理接口，可以通过web ssh或者telnet连接的接口，同时也是跟内网其他设备如认证服务器连接的接口 Management Interface Netmask: 255.255.255.0 Management Interface Default Router: 172.16.34.1 Management Interface VLAN Identifier (0 = untagged): Management Interface Port Num [1 to 8]: 1 Management Interface DHCP Server IP Address: 172.16.34.1 AP Manager Interface IP Address: 172.16.34.251 AP-Manager is on Management subnet, using same values AP Manager Interface DHCP Server (172.16.34.1): Virtual Gateway IP Address: 1.1.1.1 //设置虚拟网关 为三层漫游而设置的虚拟接口，在同一个mobility group里的WLC都必须配置相同的虚拟接口 Mobility/RF Group Name: cisco //配置Mobility/RF Group名称 用于用户在不同控制器下的AP间的三层漫游，所以不同控制器的该组必须相同 Network Name (SSID): cisco //配置默认的SSID LAP加入控制器时将使用它，LAP加入后WLC会把其他的SSID提供给LAP Allow Static IP Addresses [YES][no]: yes //客户端IP地址配置方式 yes为允许客户端使用静态IP，no则为强制客户端使用DHCP来获取IP Configure a RADIUS Server now? [YES][no]: no //配置Radius server 可后期在web界面配置 Warning! The default WLAN security policy requires a RADIUS server. Please see documentation for more details. Enter Country Code list (enter 'help' for a list of countries) [US]: cn //设置国家代码 CN表示中国，WLC的County Code要和AP一致，否则AP无法加入到WLC，如果存在使用不同的County Code的AP需要在WLC里面为其添加相应的国家码 Enable 802.11b Network [YES][no]: yes //启用802.11abg Enable 802.11a Network [YES][no]: yes Enable 802.11g Network [YES][no]: yes Enable Auto-RF [YES][no]: yes //启动自动RF检测 Configure a NTP server now? [YES][no]: no //#ntp配置 Configure the system time now? [YES][no]: no Warning! No AP will come up unless the time is set. Please see documentation for more details. Configuration correct? If yes, system will save it and reset. [yes][NO]: yes #确认配置 Restoring web auth certRestoring web auth cert Configuration saved! Resetting system with new configuration... Configuration saved! Resetting system with new configuration... //重启完成后 CISCO SYSTEMS Embedded BIOS Version 1.0(12)12 07/23/08 10:37:30.75 Low Memory: 632 KB High Memory: 507 MB PCI Device Table. Bus Dev Func VendID DevID Class Irq 00 01 00 1022 2080 Host Bridge 00 01 02 1022 2082 Chipset En/Decrypt 11 00 0C 00 1148 4320 Ethernet 11 00 0D 00 177D 0003 Network En/Decrypt 10 00 0F 00 1022 2090 ISA Bridge 00 0F 02 1022 2092 IDE Controller 00 0F 03 1022 2093 Audio 10 00 0F 04 1022 2094 Serial Bus 9 00 0F 05 1022 2095 Serial Bus 9 Evaluating BIOS Options ... Launch BIOS Extension to setup ROMMON Cisco Systems ROMMON Version (1.0(12)12) #0: Thu Jul 24 06:25:20 MDT 2008 Platform AIR-WLC2112-K9 Launching BootLoader... Cisco Bootloader (Version 4.0.191.0) .o88b. d888888b .d8888. .o88b. .d88b. d8P Y8 `88' 88' YP d8P Y8 .8P Y8. 8P 88 `8bo. 8P 88 88 8b 88 `Y8b. 8b 88 88 Y8b d8 .88. db 8D Y8b d8 `8b d8' `Y88P' Y888888P `8888Y' `Y88P' `Y88P' Booting Primary Image... Press <ESC> now for additional boot options... Detecting hardware . . . . € Cryptographic library self-test....passed! XML config selected Validating XML configuration Cisco is a trademark of Cisco Systems, Inc. Software Copyright Cisco Systems, Inc. All rights reserved. Cisco AireOS Version 6.0.199.4 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Starting ARP Services: ok Starting Trap Manager: ok Starting Network Interface Management Services: ok Starting System Services: ok Starting FIPS Features: ok : Not enabled Starting Fastpath Hardware Acceleration: ok Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok Starting Policy Manager: ok Starting Authentication Engine: ok Starting Mobility Management: ok Starting Virtual AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Power Over Ethernet Services: ok Starting Logging Services: ok Starting DHCP Server: ok Starting IDS Signature Manager: ok Starting RFID Tag Tracking: ok Starting Mesh Services: ok Starting TSM: ok Starting CIDS Services: ok Starting Ethernet-over-IP: ok Starting DTLS server: enabled in CAPWAP Starting FMC HS: ok Starting WIPS: ok Starting SSHPM LSC PROV LIST: ok Starting RRC Services: ok Starting Management Services: Web Server: ok CLI: ok Secure Web: ok (Cisco Controller) Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults) User: cisco Password:***** (Cisco Controller) > 二 web页面配置 浏览器输入WLC的管理接口IP地址 https://192.168.99.250 注意：是https
出现上图选择Login，然后输入账号和密码后登陆，登陆后如图
|
